Book Today!

 

Presented here below you can discover more decent ideas pertaining to Installing A Bathtub.

Mounting a tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old tub is easily easily accessible, the task can move speedily; if you need to open up a wall to eliminate the old bathtub as well as place the new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have qualified on your own for the task as well as are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed project, it is far better to think about using one before you begin. Chances are you may require an expert plumber to make tube connections.
This short article will certainly assist you install a new tub in your restroom if you have actually currently gotten a brand-new bathtub and don't require to alter the arrangement of your previous water pipes.
Your devices and product list must consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The process of removing the existing faucets can be quite troublesome due to the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making sure that the washing machines remain in location in between the tap as well as the sink. Protect the tap in position with the producer supplied backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind must be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Mounting the Bathtub

Utilizing the two wooden boards under its feet, place the tub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the bath tub up until the spirit level checks out degree.
To install faucets, fit the bottom of the outermost adaptable tap port to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Switch on the water and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill the bathtub and also check the overflow outlet and the regular outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the tub ought to wait till the tub has been utilized at least once as this will settle it into its final position.

 

 

Preparing for the Installment

First of all, the supporting framework supplied with the bath needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.

 

 

Tiling Around the Tub

In the area where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a rigid seal, causing the water to permeate the wall surface between the bath and the tiling, leading to complications with dampness as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also installations. They are marketed in tubes and also cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can break fairly very early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily available on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We are very inquisitive about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you liked our entry. Please take the time to promote this blog posting if you appreciated it. Thanks for your time. Visit again soon.

Schedule A Service